Prepare NACE-CIP2-001 Question Answers Free Update With 100% Exam Passing Guarantee [2021]
Dumps Real NACE NACE-CIP2-001 Exam Questions [Updated 2021]
NEW QUESTION 28
Coating Surveys are legally required:
- A. On commercial marine vessels and offshore platforms
- B. On high pressure gas lines and fireproofed structures
- C. On water tanks and potable water pipelines
- D. On food and beverage vessels and can linings
Answer: A
NEW QUESTION 29
A single component water borne acrylic coating cures by:
- A. Solvent Evaporation
- B. Coalescence
- C. Co-Reaction
- D. Oxidation
Answer: B
NEW QUESTION 30
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Sacking
- B. High-pressure water washing
- C. Stoning
- D. Acid etching
Answer: A
NEW QUESTION 31
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Comparable to air blast cleaning
- C. The same as air blast cleaning
- D. Different than air blast cleaning
Answer: C
NEW QUESTION 32
The HATE adhesion tester uses
- A. compressed air to apply pressure to the test dolly.
- B. mechanical means only to apply pressure to the test dolly.
- C. a hydraulic piston to apply pressure to the test dolly.
- D. a special tape to apply pressure to the test dolly.
Answer: C
NEW QUESTION 33
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Refuse to take readings until an is in place
- C. Develop your own methodology and proceed take the readings
- D. Call your supervisor
Answer: A
NEW QUESTION 34
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Distribution
- B. Transmission
- C. Midstream
- D. Gathering
Answer: A
NEW QUESTION 35
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Coal Tar Enamel
- B. Concrete
- C. Liquid epoxies
- D. Heat-shrink sleeves
Answer: C
NEW QUESTION 36
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. High Voltage AC
- B. Low Voltage Sponge Type
- C. High Voltage DC Constant Current
- D. High Voltage DC Pulse Type
Answer: C
NEW QUESTION 37
The Concrete Repair Institute's comparators can be used to assess:
- A. Compressive and tensile strength prior to coating
- B. Surface profile prior to coating
- C. Surface cleanliness prior to coating
- D. Contamination levels prior to coating
Answer: B
NEW QUESTION 38
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A mechanical adhesion tester
- C. A destructive paint inspection Tooke gauge
- D. A hardness tester
Answer: C
NEW QUESTION 39
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. False
- B. True
Answer: B
NEW QUESTION 40
Corrosion is the reverse process of
- A. flaking.
- B. steel manufacturing.
- C. galvanic deterioration.
- D. hot dipping.
Answer: B
NEW QUESTION 41
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Areas exposed to Ultra Violet light
- D. Mainline coating
Answer: B
NEW QUESTION 42
A failure caused by applying a coating too thinly is known as
- A. cracking.
- B. pinholes.
- C. chalking.
- D. failure to cure.
Answer: B
NEW QUESTION 43
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Lower the blast pressure
- C. Move the nozzle quicker
- D. Increase the standoff distance
Answer: A
NEW QUESTION 44
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Appearance
- B. Cost
- C. Safety
- D. Iron content
Answer: D
NEW QUESTION 45
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. a), b), and c)
- B. Risk of acid or caustic splashes
- C. Risk of skin
- D. Risk of chemical exposure
Answer: A
NEW QUESTION 46
......
NACE-CIP2-001 Exam Dumps, NACE-CIP2-001 Practice Test Questions: https://www.dumpstillvalid.com/NACE-CIP2-001-prep4sure-review.html
Free NACE-CIP2-001 Exam Dumps to Pass Exam Easily: https://drive.google.com/open?id=1MLc6IlCgFxfllFxC1HQp6BgYYIHn8Pn0
