NACE-CIP2-001 Actual Questions Answers PDF 100% Cover Real Exam Questions
NACE-CIP2-001 Exam questions and answers
NEW QUESTION # 18
The Inspectors' goal at the Pre-Job Conference is to:
- A. Take accurate meeting minutes for distribution
- B. Manage the meeting so it doesn't go off topic
- C. Obtain a clear understanding of the Specification
- D. Discuss contractual requirements
Answer: C
NEW QUESTION # 19
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. False
- B. True
Answer: B
NEW QUESTION # 20
When environmental enclosures are being used an inspector needs to be concerned about:
- A. a), b), and c)
- B. Air changes
- C. Structural integrity
- D. Lighting
Answer: A
NEW QUESTION # 21
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Wetting stage
- B. Flow stage
- C. Gel stage
- D. Cure stage
Answer: B
NEW QUESTION # 22
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Water Jetting Equipment
- B. Power Tools
- C. Scarifiers
- D. Abrasive Blasting Equipment
Answer: A
NEW QUESTION # 23
Which is used to calibrate a pH meter?
- A. Distilled water
- B. Deionized water
- C. Standard solvent solution
- D. Standard buffer solution
Answer: D
NEW QUESTION # 24
Ideally, documentation requirements should be defined:
- A. In the specification
- B. At the pre-job conference
- C. By the inspector
- D. By the contractor
Answer: A
NEW QUESTION # 25
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that have been modified for concrete
- C. Methods that are completely different to steel
- D. Methods that are the same as wood
Answer: B
NEW QUESTION # 26
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. 2-Layer Polyethylene (PE)
- B. Fusion Bonded Epoxy
- C. 3-Layer Polyethylene (PE)
- D. Coal Tar Enamel
Answer: C
NEW QUESTION # 27
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. provide protection against soil chemicals.
- C. protect the transported product.
- D. reduce magnetic polarity.
Answer: C
NEW QUESTION # 28
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Stop the job
- B. Ignore the situation
- C. Advise the Owner and write a Non-Conformance report
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION # 29
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Lower the blast pressure
- C. Increase the standoff distance
- D. Move the nozzle quicker
Answer: A
NEW QUESTION # 30
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Develop your own methodology and proceed take the readings
- C. Refuse to take readings until an is in place
- D. Call your supervisor
Answer: A
NEW QUESTION # 31
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. Concrete
- B. Coal Tar Enamel
- C. 2-Layet Polyethylene (PE)
- D. 3-Layet Polyethylene (PE)
Answer: A
NEW QUESTION # 32
Coating application to concrete substrates is:
- A. Less challenging, than coating steel
- B. Not required as Concrete is inorganic
- C. The same as coating steel
- D. More challenging than coating steel
Answer: D
NEW QUESTION # 33
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Call your supervisor
- C. Review the standard with the Contractor and re-inspect the floor
- D. Request that the Contractor re-blast the floor
Answer: C
NEW QUESTION # 34
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Mandatory
- B. De facto
- C. Voluntary
- D. Consensus
Answer: C
NEW QUESTION # 35
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Eddy Current Gauge
- B. Ultra Sonic DFT Gauge
- C. Tooke Gauge
- D. Magnetic Gauge
Answer: C
NEW QUESTION # 36
The HATE adhesion tester uses
- A. mechanical means only to apply pressure to the test dolly.
- B. compressed air to apply pressure to the test dolly.
- C. a special tape to apply pressure to the test dolly.
- D. a hydraulic piston to apply pressure to the test dolly.
Answer: D
NEW QUESTION # 37
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Inspector to decide which one to follow
- B. The Specification prevails
- C. It is up to the Applicator to decide which one to follow
- D. The Product Data Sheet prevails
Answer: B
NEW QUESTION # 38
The most likely area of failure on a buried external pipeline coating is the:
- A. Field joint coating
- B. Ground bed
- C. Areas exposed to Ultra Violet light
- D. Mainline coating
Answer: A
NEW QUESTION # 39
When observing fabrication defects the NACE Inspector should:
- A. Consult the specification to determine how they should be treated
- B. Write an NCR and call the fabricator
- C. Require they be corrected prior to coating
- D. Stop the job immediately
Answer: A
NEW QUESTION # 40
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Distribution
- B. Transmission
- C. Gathering
- D. Midstream
Answer: A
NEW QUESTION # 41
......
To be eligible for the NACE-CIP2-001 certification exam, candidates must have completed the Level 1 certification and have at least two years of experience working as a coating inspector. NACE-CIP2-001 exam covers a wide range of topics, including coating types, application methods, surface preparation, inspection techniques, and safety procedures. Coating Inspector Level 2 certification is recognized globally and is highly regarded in the coating industry.
The NACE NACE-CIP2-001 exam consists of two parts: a written exam and a practical exam. The written exam consists of 120 multiple-choice questions that cover the various topics related to coatings inspection. The practical exam involves hands-on testing of the candidate's ability to perform coating inspections and quality control procedures. The practical exam is conducted in a laboratory setting and requires the candidate to demonstrate their proficiency in using various inspection tools and equipment.
DumpStillValid NACE-CIP2-001 Exam Practice Test Questions: https://www.dumpstillvalid.com/NACE-CIP2-001-prep4sure-review.html
Pass NACE-CIP2-001 Exam Info and Free Practice Test: https://drive.google.com/open?id=16LB3jF9fRZbpyxCtclixbD3I9KyGFA67
