Free INSTC_V8 pdf Files With Updated and Accurate Dumps Training
Top-Class INSTC_V8 Question Answers Study Guide
NEW QUESTION # 93
In a commercial environment, if your horizontal cable run is 92 m (302 ft) from the TR to the Work Area, which action is recommended to remain within channel length standards?
- A. Use plenum-rated cable to extend the allowable distance
- B. Add an additional TR closer to the Work Area
- C. Convert the horizontal run to a multi-mode fiber link
- D. Utilize Category 7 cable instead of Category 6
Answer: B
NEW QUESTION # 94
When planning horizontal cable pathways in a large commercial environment, BICSI recommends that no cross-sectional fill rate exceed what percentage for conduit containing telecommunications cabling?
- A. 50%
- B. 60%
- C. 40%
- D. 25%
Answer: C
NEW QUESTION # 95
How much sheath of the cable needs to be removed in order to properly terminate an 8P8C?
- A. 25mm (1")
- B. 6.3mm (0.25")
- C. 12.7mm (0.5")
- D. 38 mm (1.5")
Answer: C
NEW QUESTION # 96
Which of the refers to a rule or set of rules intended to endure safety during the installation and use of materials, components, fixtures, systems, premises and related subjects?
- A. Standard
- B. Code
- C. Directive
- D. Regulation
Answer: B
NEW QUESTION # 97
Which of the following components is used to bond the electrical system's grounding electrode system to the PBB?
- A. BBC
- B. TBB
- C. TBC
- D. RBB
Answer: C
NEW QUESTION # 98
Which of the following describes a situation where a BICSI Installer 2 may have to calculate a cable's derating factor?
- A. When running cable vertically without any horizontal transitions
- B. When installing cables in plenum-rated air-handling spaces
- C. When bundling large numbers of cables together, impacting heat dissipation
- D. When running cables in environments below -20°C (-4°F)
Answer: C
NEW QUESTION # 99
Which of the following tools is a low-cost cable verifier that can be used to test for opens, shorts, crossed pairs, and miswires in 4- pair cables?
- A. Qualification tester
- B. Wire map tester
- C. TDR
- D. Telephone test set
Answer: B
NEW QUESTION # 100
Which of the following is a floor serving space that serves as a point of termination for horizontal and backbone cables?
- A. ER
- B. TE
- C. EF
- D. TR
Answer: D
NEW QUESTION # 101
What is the maximum number of work areas that a CP should serve?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 102
Which of the following are typically used to support cables between a cable tray and work area outlets?
- A. Innerduct
- B. Pipe hanger
- C. Trapeze
- D. J-Hook
Answer: D
NEW QUESTION # 103
Which tool is required to pull backbone cable of significant weight?
- A. Furcating harness
- B. Pulling eye
- C. Pull string
- D. Tugger
Answer: D
NEW QUESTION # 104
Which of the following is used to perform continuity and length tests for coaxial cable?
- A. OTDR (optical time domain reflectometer
- B. TDR (Time domain reflectometer) with an adapter
- C. OLTS (optical loss test set)
- D. VFL (visual fault locator)
Answer: B
NEW QUESTION # 105
What is the required physical topology for a SCS?
- A. Bus
- B. Star
- C. Tree
- D. Ring
Answer: B
NEW QUESTION # 106
A third 90-degree bend may be permitted in a conduit run if one of the bends is located within ____ of the cable feed end?
- A. 375 mm (15")
- B. 450 mm (18")
- C. 300 mm (12")
- D. 483mm (19")
Answer: C
NEW QUESTION # 107
Which of the following steps should be performed first when an installer is pulling backbone cable from the bottom up?
- A. Verify the proper cable run
- B. Label cables and reels
- C. Move cable reels into place
- D. Determine appropriate rope size
Answer: A
NEW QUESTION # 108
Fall protection is required whenever a person is exposed to a fall hazard more than ____?
- A. 1.83 m (6')
- B. 1.2 m (4')
- C. 3 m (10')
- D. 2.4 m (8')
Answer: A
NEW QUESTION # 109
Which of the following items may be used as a substitute device for a pulling eye?
- A. Innerduct
- B. D rings
- C. Wire mesh grip
- D. Fan-out kit
Answer: C
NEW QUESTION # 110
Which term describes using an LC connector on a fiber cable for the main cable plant side, and SC connector for the equipment side, in the same patch panel adapter?
- A. Transitional attenuation
- B. Mode mixing
- C. Duplex bridging
- D. Hybrid adapter coupling
Answer: D
NEW QUESTION # 111
......
Real Updated INSTC_V8 Questions & Answers Pass Your Exam Easily: https://www.dumpstillvalid.com/INSTC_V8-prep4sure-review.html
Easily To Pass New INSTC_V8 Verified & Correct Answers: https://drive.google.com/open?id=1Ug2Gb-e8OSZg3gjqNOuOSzKpzXdYqa_8
