A Fully Updated 2024 300-730 Exam Dumps - PDF Questions and Testing Engine
Easy Success Cisco 300-730 Exam in First Try
What is the salary of a Cisco 300-730 certified professional?
The Average salary of different countries of Cisco 300-730 certified professional
India - 5117094 INR
United States - 67,527 USD
UK - 50980 Pounds
For more info read reference:
Cisco 300-730 exam is focused on testing the candidate's ability to configure, implement, and troubleshoot secure remote access solutions using virtual private networks (VPNs). 300-730 exam covers a wide range of topics, including VPN protocols, secure communication channels, and various VPN technologies. Candidates are also expected to have a good understanding of security policies, access control, and authentication methods.
NEW QUESTION # 102
Refer to the exhibit.
Based on the debug output, which type of mismatch is preventing the VPN from coming up?
- A. preshared key
- B. PFS
- C. interesting traffic
- D. lifetime
Answer: C
Explanation:
The first of the two TS payloads is known as TSi (Traffic Selector- initiator). The second is known as TSr (Traffic Selector-responder). TSi specifies the source address of traffic forwarded from (or the destination address of traffic forwarded to) the initiator of the Child SA pair. https://www.rfc-editor.org/rfc/rfc5996#page-40 If the responder's policy does not allow it to accept any part of the proposed Traffic Selectors, it responds with a TS_UNACCEPTABLE Notify message.
NEW QUESTION # 103
An engineer would like Cisco AnyConnect users to be able to reach servers within the 10.10.0.0/16 subnet while all other traffic is sent out to the Internet. Which IPsec configuration accomplishes this task?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_ike2vpn/configuration/xe-3s/sec-flex-vpn-xe-3s-book/sec-cfg-flex-serv.html
NEW QUESTION # 104
Refer to the exhibit.
Which VPN technology is allowed for users connecting to the Employee tunnel group?
- A. IKEv2 AnyConnect
- B. SSL AnyConnect
- C. clientless
- D. crypto map
Answer: C
Explanation:
When you configure other group policies, any attribute that you do not explicitly specify takes its value from the default group policy. To view the default group policy. https://www.cisco.com/c/en/us/td/docs/security/asa/asa72/configuration/guide/conf_gd/vpngrp.html
NEW QUESTION # 105
Refer to the exhibit.
Which type of VPN implementation is displayed?
- A. IKEv2 reconnect
- B. IKEv1 cluster
- C. IKEv2 load balancer
- D. IKEv2 backup gateway
Answer: C
NEW QUESTION # 106
Which two types of SSO functionality are available on the Cisco ASA without any external SSO servers? (Choose two.)
- A. SAML
- B. OAuth 2.0
- C. Kerberos
- D. HTTP Basic
- E. NTLM
Answer: D,E
NEW QUESTION # 107
Which requirement is needed to use local authentication for Cisco AnyConnect Secure Mobility Clients that connect to a FlexVPN server?
- A. EAP query-identity
- B. EAP-AnyConnect
- C. AnyConnect profile
- D. use of certificates instead of username and password
Answer: C
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/security/flexvpn/200555-FlexVPN-AnyConnect-IKEv2- Remote-Access.html
NEW QUESTION # 108
Refer to the exhibit.
An engineer must allow Cisco AnyConnect users to access the outside interface using protocol UDP 500/4500. In addition, these clients must be able to establish an SSL connection to update Cisco AnyConnect software over the same connection. Which two actions must be taken to achieve this goal? (Choose two.)
- A. SSL Enable DTLS must be checked on the outside interface.
- B. SSL Allow Access must be checked on the outside interface.
- C. IPsec (IKEv2) Allow Access must be checked on the outside interface.
- D. Bypass interface access lists for inbound VPN sessions must be unchecked.
- E. IPsec (IKEv2) Enable Client Services must be checked on the outside interface.
Answer: C,E
NEW QUESTION # 109
Which command shows the smart default configuration for an IPsec profile?
- A. show crypto ipsec profile default
- B. show smart-defaults ipsec profile
- C. ipsec profile does not have any smart default configuration
- D. show run all crypto ipsec profile
Answer: A
NEW QUESTION # 110
Refer to the exhibit.
Which two conclusions should be drawn from the DMVPN phase 2 configuration? (Choose two.)
- A. Next-hop-self is required.
- B. Spoke-to-spoke communication is allowed.
- C. EIGRP is used as the dynamic routing protocol.
- D. EIGRP route redistribution is not allowed.
- E. EIGRP neighbor adjacency will fail.
Answer: B,C
NEW QUESTION # 111
Which feature of GETVPN is a limitation of DMVPN and FlexVPN?
- A. enabled use of ESP or AH
- B. sequence numbers that enable scalable replay checking
- C. design for use over public or private WAN
- D. no requirement for an overlay routing protocol
Answer: D
Explanation:
one benefit of GET VPN is Simplified network design due to leveraging of native routing infrastructure (no overlay routing protocol needed) f mismatch is causing the problem with the IPsec VPN
NEW QUESTION # 112
Refer to the exhibit.
Which type of mismatch is causing the problem with the IPsec VPN tunnel?
- A. preshared key
- B. crypto access list
- C. transform set
- D. Phase 1 policy
Answer: A
Explanation:
IKE Message from X.X.X.X Failed its Sanity Check or is Malformed
This debug error appears if the pre-shared keys on the peers do not match. In order to fix this issue, check the pre-shared keys on both sides.
1d00H:%CRPTO-4-IKMP_BAD_MESSAGE: IKE message from 198.51.100.1 failed its sanity check or is malformed
https://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation-ike-protocols/5409-ipsec-debug-00.html#anc17
NEW QUESTION # 113
A network engineer must design a remote access solution to allow contractors to access internal servers. These contractors do not have permissions to install applications on their computers. Which VPN solution should be used in this design?
- A. IKEv2 AnyConnect
- B. SSL AnyConnect
- C. Clientless
- D. Port forwarding
Answer: C
NEW QUESTION # 114
Users cannot log in to a Cisco ASA using clientless SSLVPN. Troubleshooting reveals the error message "WebVPN session terminated: Client type not supported". Which step does the administrator take to resolve this issue?
- A. Increase the simultaneous logins on the group policy.
- B. Enable the Cisco AnyConnect premium license on the Cisco ASA.
- C. Enable the clientless VPN protocol on the group policy.
- D. Have the user upgrade to a supported browser.
Answer: C
NEW QUESTION # 115
Which method dynamically installs the network routes for remote tunnel endpoints?
- A. reverse route injection
- B. CEF
- C. policy-based routing
- D. route filtering
Answer: A
Explanation:
Reference:
<https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_vpnav/configuration/12-4t/sec-vpn- availability-12-4t-book/sec-rev-rte-inject.html>
NEW QUESTION # 116
Which technology and VPN component allows a VPN headend to dynamically learn post NAT IP addresses of remote routers at different sites?
- A. GETVPN with NHRP
- B. GETVPN with ISAKMP
- C. DMVPN with ISAKMP
- D. DMVPN with NHRP
Answer: D
NEW QUESTION # 117
Refer to the exhibit.
All internal clients behind the ASA are port address translated to the public outside interface that has an IP address of 3.3.3.3. Client 1 and client 2 have established successful SSL VPN connections to the ASA. What must be implemented so that "3.3.3.3" is returned from a browser search on the IP address?
- A. Exclude Network List Below under Group Policy
- B. Tunnel All Networks under Group Policy
- C. Same-security-traffic permit inter-interface under Group Policy
- D. Tunnel Network List Below under Group Policy
Answer: B
Explanation:
The reason is that by default, the SSL VPN clients use split tunneling, which means they only send traffic destined for the corporate network through the VPN tunnel, and use their local gateway for other traffic, such as browsing the internet. This means that when they search for their IP address on a browser, they will see their local IP address, not the IP address of the ASA.
To change this behavior, you need to configure the Group Policy on the ASA to tunnel all networks, which means that all traffic from the SSL VPN clients will go through the VPN tunnel, regardless of the destination. This way, when they search for their IP address on a browser, they will see the IP address of the ASA, which is 3.3.3.3.
To configure tunnel all networks under Group Policy, you can use either ASDM or CLI. For example, using ASDM, you can follow these steps1:
Choose Configuration > Remote Access VPN > Network (Client) Access > Group Policies.
Select the group policy that you want to modify and click Edit.
In the Edit Internal Group Policy window, choose Advanced > Split Tunneling.
In the Policy drop-down list, choose Tunnel All Networks.
Click OK and then Apply.
Using CLI, you can enter these commands:
ciscoasa(config)# group-policy <group_policy_name> attributes ciscoasa(config-group-policy)# split-tunnel-policy tunnelall
NEW QUESTION # 118
A network engineer is setting up Cisco AnyConnect 4.9 on a Cisco ASA running ASA software 9.1. Cisco AnyConnect must connect to the Cisco ASA before the user logs on so that login scripts can work successfully. In addition, the VPN must connect without user intervention. Which two key steps accomplish this task? (Choose two.)
- A. Create a Cisco AnyConnect VPN profile with Always On set to true.
- B. Create a Network Access Manager profile with a client policy set to connect before user logon.
- C. Create a Cisco AnyConnect VPN profile with Start Before Logon set to true.
- D. Create a Cisco Anyconnect VPN Management Tunnel profile.
- E. Issue an identity certificate to the trusted root CA folder in the machine store.
Answer: C,E
Explanation:
https://www.cisco.com/c/en/us/support/docs/security/adaptive-security-appliance-asa-software/215442-configure-anyconnect-management-vpn-tunn.html
NEW QUESTION # 119
Why must a network engineer avoid usage of the default X.509 certificate when implementing clientless SSLVPN on an ASA?
- A. The default X.509 certificate is not supported for SSLVPN.
- B. The certificate must be managed by the local CA.
- C. The certificate is too weak to provide adequate security.
- D. The certificate is regenerated at each reboot.
Answer: D
Explanation:
By default, the ASA generates a self-signed X.509 certificate upon startup. This certificate is used in order to serve client connections by default. It is not recommended to use this certificate because its authenticity cannot be verified by the browser. Furthermore, this certificate is regenerated upon each reboot so it changes after each reboot. https://www.cisco.com/c/en/us/support/docs/security-vpn/webvpn-ssl-vpn/119417-config-asa-00.html
NEW QUESTION # 120
Refer to the exhibit.
Which type of Cisco VPN is shown for group Cisc012345678?
- A. DMVPN
- B. GETVPN
- C. Clientless SSLVPN
- D. Cisco AnyConnect Client VPN
Answer: D
NEW QUESTION # 121
Which parameter must match on all routers in a DMVPN Phase 3 cloud?
- A. NHRP network ID
- B. EIGRP split-horizon setting
- C. GRE tunnel key
- D. tunnel VRF
Answer: C
Explanation:
NHRP network IDs are locally significant and can be different. It makes sense from a deployment and maintenance perspective to use unique network ID numbers (using the ip nhrp network-id command) across all routers in a DMVPN network, but it is not necessary that they be the same. https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/15-mt/sec-conn-dmvpn-15-mt-book/sec-conn-dmvpn-dmvpn.html
NEW QUESTION # 122
......
300-730 Study Material, Preparation Guide and PDF Download: https://www.dumpstillvalid.com/300-730-prep4sure-review.html
Best 300-730 Exam Dumps for the Preparation of Latest Exam Questions: https://drive.google.com/open?id=1KYU9pDmQfWdhGvIxsXb0U8hUkAbqYz5U
